THINKCAR Thinkscan SD6 (6 Systems) 5 special functions – ALL Car Brands!

Thinkcar Thinkscan SD6 is a new generation of mid-range product based on Android launched by THINKCAR with Software developed by  LAUNCH, with FREE SOFTWARE UPDATES for life. Thinkscan SD6 can perform diagnosis of 6 electronic control systems on ALL CAR BRANDS compared to only 4 systems on Launch CRP123X or CRP129X. Thinkscan SD6 also supports more brands than 123X/129X such as Aston Martin, Daihatsu, GWM, Haval, Iveco, Tata, Mahindra.

Thinkscan SD6 Supports ABS SRS ECM TCM BCM IC systems diagnostics:

1. ENG: Engine System

THINKSCAN SD6 Scanner tool helps you read fault codes and shows the definition of DTC , clear the error, and turn off the MIL (Engine Malfunction Indicator Light).The instantaneous change of real-time data information can quickly identify the problem of Engine components, which is helpful to find out the cause of engine system errors before sending your vehicle to a repair shop.

2. AT: Transmission System

THINKSCAN SD6 Auto code reader Thinkscan SD6 diagnostic scanner is an automatic Transmission service tool that supports reading/erasing codes, viewing live data, tell you the running status of the sensors, read the error and turning off the warning light, which is helpful to quickly and accurately locate faults and solve problems easily.

3. ABS：Anti-lock Braking System

The diagnostic tool THINKSCAN SD6 is available for accessing and performing car diagnostics on Anti-lock Brake Systems respectively Whether it is the brake pad deviation, the brake pad does not return to position, or other reasons of failure. It will read ABS fault codes and tell you what the problem is through a visual inspection of all brake components, and then clear the codes. For the safety of your family, please pay attention to the health of the brake system in time.

4. SRS: Supplemental Restraint System

This OBD2 scanner tool THINKCAR SD6 supports Airbag System Diagnostic (SRS) for most domestic and imported vehicles. This scan tool can check the errors and clear the codes, view real-time live data to monitor the SRS running status, and solve security risks.Extend the service life of airbags and improve vehicle safety.

5. IC: Instrument Cluster System

The Automotive Engine Scanner THINKCAR SD6 can quickly input signals to the instrument panel and read the fault information, and at the same time store the fault code of the faulty part. When it is confirmed that the instrument panel is faulty, the instrument panel code error should be detected and cleared, which can better protect the driving safety of the car owner.

6. BCM: Body Control Module

The THINKCAR SD6 automotive Scan tool enables you to read data, calculate and analyse the data from the BCM which also generally controls the immobiliser. Calculate the data required to execute the command according to the information parameters, compare the input information with the standard value. Finally, output vehicle fault information and complete fault correction. This helps to enhance the safety, comfort and convenience of  the car.

Thinkscan SD6 detailed Demo and Review

Thinkscan SD6 Supports 28 Reset Function (Choose 5):

Pls note : You can choose 5 Reset Function Free (Yours for life), for extra reset functions you can purchase additionally for US$29.95 per reset function (±R500)

1 Oil Reset

The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset themileage or driving time to zero after the maintenance, so the maintenance light will go out and the systemwill start a new maintenance cycle.

2 Elec.Throttle Adaption

Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learningvalue of the ECU returns to the initial state.By doing these, the movement of the throttle (or idle motor)can be more accurately controlled, thus adjust the intake volume.

3 Steering Angle Reset

To reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference, the ECU can calculate the accurate angle for left and right steering.After replacing the steering angle position sensor, replacing steering mechanical parts (such as steeringgearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recoveringcar body, you must reset the steering angle.

4 Battery Matching

This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, inwhich the original low battery fault information will be cleared and battery matching will be done.

5 ABS Bleeding

When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system torestore ABS brake sensitivity. lf the ABS computer,ABS pump, brake master cylinder, brake cylinder, brakeline, or brake fluid is replaced, the ABS bleeding function must be performed to bleed the ABS.

6 Brake-pad Reset

lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to theon-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms.

7 DPF Regeneration

DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuouscombustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reducePM ignition combustion) to stabilize the filter performance.

8 Gear Learning

The crankshaft position sensor learns crankshaft gear machining tolerance and saves to the computerto more accurately diagnose engine misfires. lf gear learning is not performed for a car equipped withDelphi engine, the MlL turns on after the engine is started.The diagnostic device detects the DTC P1336’gear not learned’. In this case, you must use the diagnostic device to perform gear learning for the car.After gear learning is successful, the MIL turns off. After the engine ECU, crankshaft position sensor, orcrankshaft flywheel is replaced, or the DTC ‘gear not learned” is present, gear learning must be performed.

9 IMMO Service

To prevent the car being used by unauthorized keys, the anti-theft key matching function must beperformed so that the immobilizer control system on the car identifies and authorizes remote control keysto normally use the car. When the ignition switch key, ignition switch, combined instrument panel,ECu,BCM, or remote control battery is replaced, anti-theft key matching must be performed

10 Injector Coding

Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder soas to more accurately control or correct cylinder injection quantity. After the ECU or injector is replaced,injector code of each cylinder must be confirmed or re-coded so that the cylinder can better identifyinjectors to accurately control fuel injection.

11 TPMS Reset

After the tire pressure MIL turns on and maintenance is performed, the tire pressure resetting function must be performed to reset tire pressure and turn off the tire pressure MIL.Tire pressure resetting must be performed if tire pressure is too low, tire leaks, tire pressure monitoring device is replaced or installed, tire is replaced, tire pressure sensor is damaged, and tire is replaced for the car with tire pressure monitoring function.

12 Suspension Matching

This function can adjust the height of the body. When replacing the body height sensor in the air suspension system, or control module or when the vehicle level is incorrect, you need to perform this function to adjust the body height sensor for level calibration.

13 AFS Reset

This feature is used to initialize the adaptive headlamp system.According to the ambient light intensity, the adaptive headlamp system may decide whether to automatically turn on the headlamps, and timely adjust the headlamp lighting angle while monitoring the vehicle speed and body posture.

14 A/T Learning

This function can complete the gearbox self-learning to improve gear shifting quality. When the gearbox is disassembled or repaired (after some of the car battery is powered off), it will lead to shift delay or impact problem. In this case, this function needs to be done so that the gearbox can automatically compensate according to the driving conditions so as to achieve more comfortable and better shift quality.

15 Sunroof Initialization

This function can set the sunroof lock off, closed when it rains, sliding / tilting sunroof memory function, temperature threshold outside the car etc.

16 EGR Adaption

This function is used to learn the EGR (Exhaust Gas Recirculation) valve after it is cleaned or replaced.

17 ODO Reset

a) Odometer reset is to copy, write, or rewrite the value of kilometers in the chip of odometer by using a car
diagnostic computer and data cable, so that the odometer shows the actual mileage.

b)Usually when the mileage is not correct due to the damaged vehicle speed sensor or odometer failure, it is necessary to do ODo reset after maintenance.

18 Airbag Reset

This function resets the airbag data to clear the airbag collision fault indicator. When the vehicle collides and the airbag deploys, the corresponding fault code of the collision data appears, the airbag indicator lights up, and the fault code cannot be cleared. Since the data inside the airbag computer is disposable, it is required that all new accessories must be replaced, but after performing this function, the data of the airbag computer can be recovered and the fault code can be cleared, the airbag light will go out, and the airbag computer can continue to use.

19 Transport Mode

ln order to reduce power consumption, the following functions may be disabled, including limiting the vehicle speed, not waking up the door opening network, and disabling the remote control key, etc. At thistime, the transport mode needs to be deactivated to restore the vehicle to normal.

20 A/F Reset

This function is applied to set or learn Air/Fuel ratio parameters.

21 Stop/Start Reset

This function is used to open or close the automatic start-stop function via setting the hidden function inECU(provided that the vehicle has a hidden function and supported by hardware).

22 NOx Sensor Reset

NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. lf theNOx fault is initialised and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine ECu.

23 AdBlue Reset (Diesel Engine Exhaust Gas Filter)

After the diesel exhaust treatment fluid (car urea) is replaced or flled up, urea reset operation is required.

24 Seat Calibration

This function is applied to match the seats with memory function that are replaced and repaired.

25 Coolant Bleeding

Use this function to activate the electronic water pump before venting the cooling system.

26 Tyre Reset

This function is used to set the size parameters of the modified or replaced tire.

27 Windows Calibration

This feature is designed to perform door window matching to recover ECU initial memory, and recover theautomatic ascending and descending function of power window.

28 Language Change

This function is used to change the system language of the vehicle central control panel.

ThinkScan SD6 supports Full OBD2 Function Diagnosis

• Reading Codes
• Erasing Codes & Reset
• Data Stream
• Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.
• I/M Readiness Status
• Read Live Data Stream
• View Freeze Frame Data
• O2 Sensor Test
• On-Board Monitor Test
• Read Vehicle Information
• Component Test

Vehicle Brands Supported by Thinkscan SD6

The Thinkscan SD6 supports all car brands in the SA market including locally manufactured bakkies and special imports.